Specifications

Supply Voltage

10 V dc to 30 V dc (10% max. ripple) at less than 40 mA, exclusive of load

Protected against reverse polarity and transient voltages

Output Response

Opposed Mode: 5 milliseconds ON and OFF

All others: 2 milliseconds

NOTE: 100 millisecond delay on power-up; outputs do not conduct during this time

Repeatability

Opposed Mode: not applicable

All others: 500 microseconds

Cutoff Point Tolerance

Fixed-Field only: ± 5% of nominal cutoff distance

Construction and Mounting

ABS housing, rated IEC IP67; NEMA 6; Acrylic lens cover

3 mm mounting hardware included

Connections

2 m (6.5 ft) unterminated 5-wire PVC cable; 9 m (30 ft) unterminated 5-wire PVC

cable ; or Integral 5-pin M12/Euro-style male quick disconnect (QD)

Application Tip for the QS30LV Model

For best sensing reliability, targets should be a minimum of 0.5m from the sensor

Output Configuration

Bipolar: One current sourcing and one current sinking

Rating: 100 mA maximum each output at 25 °C

Off-state leakage current:

NPN: less than 200 μA

PNP: less than 10 μA

ON-state saturation voltage:

NPN: less than 1.6 V at 100 mA

PNP: less than 2.0 V at 100 mA

Protected against false pulse on power-up and continuous overload or short circuit of

outputs

Adjustments

Selectable Light/Dark Operate is achieved via the gray wire.

Opposed, Retroreflective, and Polarized Retroreflective models:

Light Operate - Low (0 to 3 V)*

Dark Operate - High (open or 5 to 30 V)*

Diffuse and Fixed-Field models:

Light Operate - High (open or 5 to 30 V)*

Dark Operate - Low (0 to 3 V)*

Diffuse, Retroreflective, and Polarized Retroreflective mode models (only):

Single-turn Sensitivity (Gain) adjustment potentiometer

* Input impedance 10 kΩ

Indicators

2 LEDs on sensor top:

Green

Yellow

On

Power on

Light sensed

Flashing

Output overloaded (except

receivers)

Marginal excess gain (1–1.5×

excess gain)

Large oval LED on sensor back (except emitters): Yellow on indicates the output is

conducting

Operating Conditions

–20 °C to +70 °C (–4 °F to +158 °F)

95% at +50 °C maximum relative humidity (non-condensing)

Vibration and Mechanical Shock

All models meet Mil Std. 202F requirements. Method 201A (vibration: 10 Hz to 60 Hz

max., double amplitude 0.06 inch, maximum acceleration 10G). Also meets IEC

947-5-2 requirements: 30G 11 ms duration, half sine wave.

Certifications

Pending

Dimensions

33.0 mm

(1.30")

16.0 mm

(0.63")

44.0 mm

(1.73")

1.3 mm

(0.05")

22.0 mm

(0.87")

13.0 mm

(0.51")

5.0 mm

(0.20")

35.0 mm

(1.38")

2 x ø3.3 mm (0.125")

max. torque

0.7 Nm (6 in lbs)

M30 x 1.5 Thread

max. torque

6 Nm (53 in lbs)

with included 30 mm

mounting nut

Yellow LED

Output

Indicator

Yellow and Green LEDs

12.5 mm

(0.47")

Cabled Models

QD Models

All measurements are listed in millimeters [inches], unless noted otherwise.

Banner Engineering Corp. Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge,

any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or

the improper application or installation of the Banner product.

THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.

This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER

PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR

FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner

Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such

purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this

document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is

provided in any other language. For the most recent version of any documentation, refer to:

www.bannerengineering.com.