RF63W datasheet(39/91 Pages) HOPE

39 / 91 page

ADVANCED COMMUNICATIONS & SENSING

Page 39 of 91

RF63

Tel: +86-755-82973805 Fax: +86-755-82973550 E-mail: sales@hoperf.com http://www.hoperf.com

5.2.2.3. Interrupt Sources and Flags

All interrupt sources and flags are configured in the IRQParam section of the configuration register, with the

exception of Fifo_threshold :

•

/Fifoempty: /Fifoempty interrupt source is low when byte 0, i.e. whole FIFO, is empty. Otherwise it is high. Note

that when retrieving data from the FIFO, /Fifoempty is updated on NSS_DATA falling edge, i.e. when

/Fifoempty is updated to low state the currently started read operation must be completed. In other words,

/Fifoempty state must be checked after each read operation for a decision on the next one (/Fifoempty = 1:

more byte(s) to read; /Fifoempty = 0: no more byte to read).

•

Write_byte: W rite_byte interrupt source goes high for 1 bit period each time a new byte is transferred from the

SR to the FIFO (i.e. each time a new byte is received)

•

Fifofull: Fifofull interrupt source is high when the last FIFO byte, i.e. the whole FIFO, is full. Otherwise it is low.

•

Fifo_overrun_clr: Fifo_overrun_clr flag is set when a new byte is written by the user (in Tx or Standby modes)

or the SR (in Rx mode) while the FIFO is already full. Data is lost and the flag should be cleared by writing a 1,

note that the FIFO will also be cleared.

•

Tx_done: Tx_done interrupt source goes high when FIFO is empty and the SR

‟s last bit has been send to the

modulator (i.e. the last bit of the packet has been sent). One bit period delay is required after the rising edge of

Tx_done to ensure correct RF transmission of the last bit. In practice this may not require special care in the uC

software due to IRQ processing time.

•

Fifo_threshold: Fifo_threshold interrupt source

‟s behavior depends on the running mode (Tx, Rx or Stby mode)

and the threshold itself can be programmed via MCParam_Fifo_thresh (B value). This behavior is illustrated in

Figure 32.

IRQ source

B+1 B+2

# of bytes in FIFO

Rx & Stby

Figure 32: FIFO Threshold IRQ Source Behavior

5.2.2.4. FIFO Clearing

Table 16 below summarizes the status of the FIFO when switching between different modes

Table 16: Status of FIFO when Switching Between Different Modes of the Chip

From

FIFO Status

Comments

Stby

Cleared

In Buffered mode, FIFO cannot be written in Stby before Tx

Not cleared

In Packet mode, FIFO can be written in Stby before Tx

Stby

Cleared

Stby

Not cleared

In Packet & Buffered modes FIFO can be read in Stby after Rx

Cleared

Stby

Not cleared

Any

Sleep

Cleared

RF63W датащи(PDF) 39 Page - HOPE Microelectronics CO., Ltd.

RF63W датащи(HTML) 39 Page - HOPE Microelectronics CO., Ltd.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91

датащи скачать

ссылки URL