38

CAT.8100H

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

Performance Characteristics

Item

–55 to +105°C

2.5 to 25V

3.3 to 1500µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C

Z+105°C / Z+20°C

1.25

(100kHz)

Z

–55°C / Z+20°C

1.25

Endurance

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 105°C

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 60°C, 90% RH.

After soldering the capacitor under the soldering conditions

prescribed here, the capacitor shall meet the specifications listed

at right.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface

shall not exceed 60 seconds.

In case peak temperature is 250°C or less, reflow soldering shall

be two times maximum.

In case peak temperature is 260°C or less, reflow soldering shall

be once.

Measurement for solder temperature profile shall be made at the

capacitor top and the terminal.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of the initial capacitance value ( 3)

150% or less than the initial specified value

150% or less than the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

Low ESR, High ripple current.

Load life of 2000 hours at 105°C.

SMD type : Lead free reflow soldering condition at 260°C

peak correspondence.

Compliant to the RoHS directive (2011/65/EU).

AEC-Q200 compliant. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

φD

4 to 6.3

（5.5L）

5 to 10

（L 6）

Code

GB

GS

P

1

C

2

F

3

0

4

J

5

1

6

5

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Size code

Capacitance tolerance (±20%)

Rated capacitance (150µF)

Rated voltage (6.3V)

Series name

Type

H

0.3 MAX.

C±0.2

L

Series

Voltage ( j:6.3v)

Plastic platform

Lot No.

Capacitance

Negative

Positive

+0.1

-0.4

Dimensions

Type numbering system (Example : 6.3V 150µF)

Voltage

V

2.5

4

6.3

10

16

20

25

Code

e

g

j

A

C

D

E

Size

φD

L

A

B

C

E

H

φ4

4.0

5.4

5.0

4.3

4.3

1.0

0.5 to 0.8

φ5

5.0

5.9

6.0

5.3

5.3

1.6

0.5 to 0.8

φ6.3

6.3

5.4

7.3

6.6

6.6

2.1

0.5 to 0.8

φ6.3

6.3

5.9

7.3

6.6

6.6

2.1

0.5 to 0.8

φ8

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8

8.0

11.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ10

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

(mm)

Dimension table in next page.

Higher Capacitance

PCJ

Long Life

PCS

Higher

Capacitance,

PCG

Frequency coefficient of rated ripple current

Coefficient

120Hz 1kHz 10kHz 100kHz or more

0.05

0.30

0.70

1.00

φ4×5.5L which are scheduled to be discontinued.

Not recommended for new designs.