54

CAT.8100H

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

Performance Characteristics

Item

–55 to +125°C

16 to 80V

22 to 1000µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(µA), whichever is greater.

Z+125°C / Z+20°C

1.25

(100kHz)

Z

–55°C / Z+20°C

1.25

Endurance

Shelf Life

ESR after Endurance ( 1)

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 4000 hours at 125°C.

Less than or equal to the specified value at 100kHz, -40°C

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 1000 hours at 85°C, 85% RH.

After soldering the capacitor under the soldering conditions

prescribed here, the capacitor shall meet the specifications listed at

right.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface shall

not exceed 60 seconds.

In case peak temperature is 260°C or less, reflow soldering shall be

two times maximum.

Measurement for solder temperature profile shall be made at the

capacitor top and the terminal.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of initial capacitance value ( 3)

150% or less of the initial specified value

200% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 20% of initial capacitance value ( 3)

150% or less of the initial specified value

200% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

High reliability, High voltage (to 80V).

Low ESR, High ripple current.

Long life of 4000 hours at 125°C.

SMD type : Lead free reflow soldering condition at

260°C peak complete correspondence.

Compliant to the RoHS directive (2011/65/EU).

ESR after Endurance at -40°C.

AEC-Q200 compliant. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

P

1

C

2

R

3

1

4

V

5

1

6

5

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Size code

Capacitance tolerance (±20%)

Rated capacitance (150µF)

Rated voltage (35V)

Series name

Type

Standard

Vibration Resistance

code

Configuration

L

S

Type numbering system (Example : 35V 150µF)

Dimension table in next page.

φD

L

A

B

C

E

H

Size

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8 × 7L

8.0

9.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8 × 10L

8.0

11.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8 × 12L

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10 × 8L

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10 ×10L

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10×12.7L

(mm)

Code C

V

16

D

20

E

25

V

35

H

50

J

63

K

80

Voltage

φD

L

A

B

C

E

H

Size

8.0

10.0

9.0

8.3

8.3

3.1

1.1 to 1.5

φ8×10.5L

10.0

10.0

11.0

10.3

10.3

4.6

1.1 to 1.5

φ10×10.5L

6.3

7.5

7.3

6.6

6.6

2.5

0.5 to 0.8

φ6.3 ×8L

10.0

12.7

11.0

10.3

10.3

4.6

1.1 to 1.5

φ10×13.2L

(mm)

Vibration Resistance

Standard

PCR

High Capacitance

Long Life Assurance

PCX

After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4

clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.

Frequency coefficient of rated ripple current

Frequency

Coefficient

120Hz 1kHz 10kHz 100kHz or more

0.05 0.30 0.70

1.00

φ8×10L, φ10×10L, φ10×12.7L : The vibration structure-resistant product

is also available upon request, please ask for details.

H

0.3 MAX.

C±0.2

L

Series

Voltage (V:35V)

Plastic platform

Lot No.

Capacitance

Negative

Negative

Positive

Positive

+0.1

-0.4

Standard

Vibration Resistance

H

0.3 MAX.

C±0.2

L±0.5

Plastic platform

Aid electrode

Series

Voltage (V:35V)

Lot No.

Capacitance

Dimensions