CAT93C76 datasheet(2/15 Pages) ONSEMI

2 / 15 page

CAT93C76

www.onsemi.com

Table 1. ABSOLUTE MAXIMUM RATINGS

Parameters

Ratings

Units

Temperature Under Bias

−55 to +125

°C

Storage Temperature

−65 to +150

°C

Voltage on any Pin with Respect to Ground (Note 1)

−2.0 to +VCC +2.0

VCC with Respect to Ground

−2.0 to +7.0

Lead Soldering Temperature (10 seconds)

300

°C

Output Short Circuit Current (Note 2)

100

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

1. The minimum DC input voltage is −0.5 V. During transitions, inputs may undershoot to −2.0 V for periods of less than 20 ns. Maximum DC

voltage on output pins is VCC +0.5 V, which may overshoot to VCC +2.0 V for periods of less than 20 ns.

2. Output shorted for no more than one second.

Table 2. RELIABILITY CHARACTERISTICS (Note 2)

Symbol

Parameter

Reference Test Method

Min

Units

NEND (Note 3)

Endurance

MIL−STD−883, Test Method 1033

1,000,000

Cycles / Byte

TDR (Note 3)

Data Retention

MIL−STD−883, Test Method 1008

100

Years

VZAP (Note 3)

ESD Susceptibility

MIL−STD−883, Test Method 3015

2,000

ILTH (Notes 3, 4)

Latch−Up

JEDEC Standard 17

100

3. These parameters are tested initially and after a design or process change that affects the parameter.

4. Latch−up protection is provided for stresses up to 100 mA on I/O pins from −1 V to VCC + 1 V.

Table 3. D.C. OPERATING CHARACTERISTICS (VCC = +1.8 V to +5.5 V unless otherwise specified.)

Symbol

Parameter

Test Conditions

Min

Typ

Max

Units

ICC1

Power Supply Current (Write)

fSK = 1 MHz, VCC = 5.0 V

ICC2

Power Supply Current (Read)

fSK = 1 MHz, VCC = 5.0 V

300

500

ISB1

Power Supply Current

(Standby) (x8 Mode)

CS = 0 V, ORG = GND

ISB2

Power Supply Current

(Standby) (x16 Mode)

CS = 0 V, ORG = Float or VCC

0 (Note 5)

ILI

Input Leakage Current

VIN = 0 V to VCC

0 (Note 5)

ILO

Output Leakage Current

VOUT = 0 V to VCC, CS = 0 V

0 (Note 5)

ILORG

ORG Pin Leakage Current

ORG = GND or ORG = VCC

VIL1

Input Low Voltage

4.5 V v VCC v 5.5 V

−0.1

0.8

VIH1

Input High Voltage

4.5 V v VCC v 5.5 V

VCC + 1

VIL2

Input Low Voltage

1.8 V v VCC < 4.5 V

VCC x 0.2

VIH2

Input High Voltage

1.8 V v VCC < 4.5 V

VCC x 0.7

VCC + 1

VOL1

Output Low Voltage

4.5 V v VCC v 5.5 V, IOL = 2.1 mA

0.4

VOH1

Output High Voltage

4.5 V v VCC v 5.5 V, IOH = −400 mA

2.4

VOL2

Output Low Voltage

1.8 V v VCC < 4.5 V, IOL = 100 mA

0.1

VOH2

Output High Voltage

1.8 V v VCC < 4.5 V, IOH = −100 mA

VCC − 0.2

5. 0 mA is defined as less than 900 nA.

Table 4. PIN CAPACITANCE (Note 3)

Symbol

Test

Conditions

Min

Typ

Max

Units

COUT

Output Capacitance (DO)

VOUT = 0 V

CIN

Input Capacitance (CS, SK, DI, ORG)

VIN = 0 V

CAT93C76 датащи(PDF) 2 Page - ON Semiconductor

CAT93C76 датащи(HTML) 2 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

датащи скачать

ссылки URL