| поискавой системы для электроныых деталей |
|
SCF5250 датащи(PDF) 32 Page - Motorola, Inc |
|
|
|||||||||||||||||||||||||||||
SCF5250 датащи(HTML) 32 Page - Motorola, Inc |
|
32 / 48 page ![]() SCF5250 Integrated ColdFire® Microprocessor Data Sheet, Rev. 1.1 Electrical Characteristics Freescale Semiconductor 32 Table 25. I2C-Bus Input Timing Specifications Between SCL and SDA Num Characteristic Units Min Max M1 Start Condition Hold Time 2 — bus clocks M2 Clock Low Period 8 — bus clocks M3 SCL/SDA Rise Time (VIL= 0.5 V to VIH = 2.4 V) —1 mSec M4 Data Hold Time 0 — nSec M5 SCL/SDA Fall Time (VIH= 2.4 V to VIL = 0.5 V) —1 mSec M6 Clock High time 4 — bus clocks M7 Data Setup Time 0 — nSec M8 Start Condition Setup Time (for repeated start condition only) 2 — bus clocks M9 Stop Condition Setup Time 2 — bus clocks Table 26. I2C-Bus Output Timing Specifications Between SCL and SDA Num Characteristic Units Min Max M11 Start Condition Hold Time 6 — bus clocks M21 Clock Low Period 10 — bus clocks M32 SCL/SDA Rise Time (VIL= 0.5 V to VIH = 2.4 V) note 2 note 2 mSec M41 Data Hold Time 7 — bus clocks M53 SCL/SDA Fall Time (VIH= 2.4 V to VIL = 0.5 V) — 3 nSec M61 Clock High time 10 — bus clocks M71 Data Setup Time 2 — bus clocks M81 Start Condition Setup Time (for repeated start condition only) 20 — bus clocks M91 Stop Condition Setup Time 10 — bus clocks 1. Note: Output numbers are dependent on the value programmed into the MFDR; an MFDR programmed with the maximum frequency (MFDR = 0x20) will result in minimum output timings as shown in the above table. The MBUS interface is designed to scale the actual data transition time to move it to the middle of the SCL low period. The actual position is affected by the prescale and division values programmed into the MFDR; however, numbers given in the above table are the minimum values. 2. Since SCL and SDA are open-collector-type outputs, which the processor can only actively drive low, the time required for SCL or SDA to reach a high level depends on external signal capacitance and pull-up resistor values. 3. Specified at a nominal 20 pF load. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |