HIP6302CB datasheet(6/16 Pages) RENESAS

6 / 16 page

HIP6302

FN4766 Rev.3.00

Page 6 of 16

December 27, 2004

Absolute Maximum Ratings

Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+7V

Input, Output, or I/O Voltage . . . . . . . . . . GND -0.3V to VCC + 0.3V

ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class TBD

Recommended Operating Conditions

Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V

5%

Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC

Thermal Information

Thermal Resistance (Typical, Note 1)

JA (oC/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . .150oC

Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC

(SOIC - Lead Tips Only)

CAUTION: Stress above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational section of this specification is not implied.

NOTE:

JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

Electrical Specifications Operating Conditions: VCC = 5V, TA = 0oC to 70oC, Unless Otherwise Specified

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX UNITS

INPUT SUPPLY POWER

Input Supply Current

RT = 100k, Active and Disabled Maximum Limit

POR (Power-On Reset) Threshold

VCC Rising

4.25

4.38

4.5

VCC Falling

3.75

3.88

4.00

REFERENCE AND DAC

System Accuracy

Percent system deviation from programmed VID Codes

-1

DAC (VID0 - VID4) Input Low Voltage

DAC Programming Input Low Threshold Voltage

0.8

DAC (VID0 - VID4) Input High Voltage

DAC Programming Input High Threshold Voltage

2.0

VID Pull-Up

VIDx = 0V or VIDx = 3V

A

CHANNEL GENERATOR

Frequency, FSW

RT = 100k, 1%

245

275

305

kHz

Adjustment Range

See Figure 10

0.05

1.5

MHz

Disable Voltage

Maximum voltage at FS/DIS to disable controller. IFS/DIS = 1mA.

1.0

ERROR AMPLIFIER

DC Gain

RL = 10K to ground

Gain-Bandwidth Product

CL = 100pF, RL = 10K to ground

MHz

Slew Rate

CL = 100pF, Load = 400A-

5.3

s

Maximum Output Voltage

RL = 10K to ground, Load = 400A3.6

4.1

Minimum Output Voltage

RL = 10K to ground, Load = -400A

0.16

0.5

ISEN

Full Scale Input Current

-50

A

Over-Current Trip Level

82.5

A

POWER GOOD MONITOR

Under-Voltage Threshold

VSEN Rising

0.92

VDAC

Under-Voltage Threshold

VSEN Falling

0.90

VDAC

PGOOD Low Output Voltage

IPGOOD = 4mA

0.18

0.4

PROTECTION

Over-Voltage Threshold

VSEN Rising

1.12

1.15

1.2

VDAC

Percent Over-Voltage Hysteresis

VSEN Falling after Over-Voltage

HIP6302CB датащи(PDF) 6 Page - Renesas Technology Corp

HIP6302CB датащи(HTML) 6 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

датащи скачать

ссылки URL