All Inputs Off

f=20KHz, 50% Duty Cycle

SWR Resistor=

∞

SWR Resistor=

∞

SWR =

∞

SWR=12K

CONTROL SECTION

Undervoltage Threshold (Falling)

Undervoltage Threshold (Rising)

Low Level Input Voltage

High Level Input Voltage

Low Level Input Current

High Level Input Current

OUTPUT BRIDGE

Drain-Source Breakdown Voltage

Drain-Source Leakage Current

Drain-Source On Resistance (Each FET)

Drain-Source On Resistance

(Each FET, For Thermal Calculations Only)

SWITCHING CHARACTERISTICS

Rise Time

Fall Time

Turn-On Prop Delay (Lower)

Turn-Off Prop Delay (Lower)

Turn-On Prop Delay (Upper)

Turn-Off Prop Delay (Upper)

Dead Time

Dead Time

SOURCE-DRAIN DIODE CHARACTERISTICS

Forward Voltage

Reverse Recovery Time

75V

16V

10A

25A

High Voltage Supply

Bias Supply

Logic Input Voltages

Continuous Output Current

Peak Output Current

ABSOLUTE MAXIMUM RATINGS

V+

9°C/W

-65°C to +150°C

+300°C

-55°C to +125°C

+150°C

Thermal Resistance

Storage Temperature Range

Lead Temperature Range

(10 Seconds)

Case Operating Temperature

Junction Temperature

Typ.

2.5

12.5

6.6

7.1

-

-

100

-

-

-

-

5

6

0.5

5

5

0.5

7.0

0.5

1.05

75

mAmp

mAmp

Volts

Volts

Volts

Volts

µAmp

µAmp

V

µAmp

Ω

nSec

nSec

µSec

µSec

µSec

µSec

µSec

µSec

Volts

nSec

Parameter

ELECTRICAL SPECIFICATIONS

Units

Max.

8

15

7.5

8.0

0.8

-

135

+1

-

25

0.300

-

-

3

10

10

3

8.0

0.7

1.25

-

MSK 4300

Min.

5.75

6.2

-

2.7

60

-1

70

-

-

-

-

-

-

-

-

6.0

0.3

-

-

Test Conditions

Rev. C 6/00

2

Typ.

2.5

12.5

6.6

7.1

-

-

100

-

-

-

-

5

6

0.5

5

5

0.5

7.0

0.5

1.05

75

Max.

8

15

7.5

8.0

0.8

-

135

+1

-

25

0.300

-

-

2

8

8

2

8.0

0.7

1.25

-

MSK 4300H

Min.

5.75

6.2

-

2.7

60

-1

70

-

-

-

-

-

-

-

-

6.0

0.3

-

-

GroupA 4

Subgroup

1,2,3

1,2,3

1

1

-

-

-

-

-

-

1

-

-

4

4

4

4

4

4

-

-

NOTES:

1

Guaranteed by design but not tested. Typical parameters are representative of actual device

performance but are for reference only.

2

Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.

3

Military grade devices ("H" Suffix) shall be 100% tested to Subgroups 1, 2, 3 and 4.

4

Subgroups 5 and 6 testing available upon request.

5

1

SWR Resistor=

∞

SWR Resistor=

∞

1

1

1

1

1

1

1

1

1

3

2

-

Ω

0.16

0.16

-

-

-

-

1