LT6016 datasheet(13/22 Pages) LINER

13 / 22 page

LT6015/LT6016/LT6017

601567ff

For more information www.linear.com/LT6015

applicaTions inForMaTion

Supply Voltage

The positive supply pin of the LT6015/LT6016/LT6017

shouldbebypassedwithasmallcapacitor(typically0.1μF)

as close to the supply pins as possible. When driving

heavy loads an additional 4.7μF electrolytic capacitor

should be added. When using split supplies, the same is

true for the V– supply pin.

The LT6017 consists of two dual amplifier dice assembled

in a single DFN package which share a common substrate

(V–). While the V– pins of the quad (pins 16 and 18) must

alwaysbetiedtogetherandtotheexposedpadunderneath,

the V+ power supply pins (pins 5 and 7) may be supplied

independently.TheBandCchannelamplifiersaresupplied

through V+ by pin 7, and the A and D channel amplifiers are

supplied by pin 5. If pin 5 and pin 7 are not tied together

and are biased independently, each V+ pin should have

their own dedicated supply bypass to ground.

Shutdown

WhiletherearenodedicatedshutdownpinsfortheLT6015/

LT6016/LT6017,theamplifierscaneffectivelybeshutdown

into a low power state by removing V+. In this condition

the input bias current is typically less than 1nA with the

inputs biased between V– and 76V above V–, and if the

inputs are taken below V–, they appear as a diode in series

with 1k of resistance. The output may be pulled up to 50V

above the V+ power supply in this condition (See Figure 1).

Pulling the output pin below V– will produce unlimited

current and can damage the part.

Reverse Battery

TheLT6015/LT6016/LT6017areprotectedagainstreverse

battery voltages up to 50V. In the event a reverse battery

condition occurs, the supply current is typically less

than 5µA (assuming the inputs are biased within a diode

drop from V–). For typical single supply applications with

ground referred loads and feedback networks, no other

precautions are required. If the reverse battery condition

results in a negative voltage at the input pins, the current

into the pin should be limited by an external resistor to

less than 10mA.

Inputs

ReferringtotheSimplifiedSchematic,theLT6015/LT6016/

LT6017hastwoinputstages:acommonemitterdifferential

input stage consisting of PNP transistors Q1 and Q2 which

operate when the inputs are biased between V– and 1.5V

below V+, and a common base input stage consisting of

PNPtransistorsQ3toQ6whichoperatewhenthecommon

mode input is biased greater than V+ –1.5V. This results

in two distinct operating regions as shown in Figure 2.

For common mode input voltages approximately 1.5V or

more below the V+ supply (Q1 and Q2 active), the com-

mon emitter PNP input stage is active and the input bias

current is typically under ±2nA. When the common mode

input is within approximately 1V of the V+ supply or higher

Figure 1. LT6015/LT6016/LT6017 Fault Tolerant Conditions

INPUTS DRIVEN ABOVE

SUPPLY TOLERANT

–

OK!

80V

REVERSE BATTERY

TOLERANT

–50V

–

OK!

INPUTS DRIVEN BELOW

GROUND TOLERANT

25V

TRANSIENT

–

OK!

LARGE DIFFERENTIAL

INPUT VOLTAGE

TOLERANT

–

OK!

80V

OUTPUT DRIVEN ABOVE THE

V+ SUPPLY (IN SHUTDOWN)

TOLERANT

–

OK!

601567 F01

50V

–

LT6016 датащи(PDF) 13 Page - Linear Technology

LT6016 датащи(HTML) 13 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

датащи скачать

ссылки URL