| поискавой системы для электроныых деталей |
|
ACT2801 датащи(PDF) 15 Page - Active-Semi, Inc |
|
|
|||||||||||||||||||||||||||||
ACT2801 датащи(HTML) 15 Page - Active-Semi, Inc |
|
15 / 25 page ![]() Rev 9, 14-Mar-17 Innovative PowerTM - 15 - www.active-semi.com Copyright © 2015-2017 Active-Semi, Inc. ACT2801/ACT2801B/ACT2801C The IOST pin voltage is proportional to output current until output current is limited, as shown in Figure 15. Battery Impedance Compensation An external resistor is used to set the impedance from 40mΩ to 500mΩ as shown in Figure 16. RIMC is corresponding to battery impedance. Higher RIMC gives higher compensation voltage which is positively proportional to battery charge/discharge current. Select RIMC based on battery impedance: The battery impedance as shown in the table 4 according to the RIMC and Rcs: Table 4: Battery Impedance Input Over Voltage Surge In the case of pure ceramic input capacitor is chosen, if the input cable is long, stray inductance may cause over voltage spikes as twice as the steady-state voltage when input source is plugged in. Below input circuit is recommended to avoid input voltage surge. R1 resistor is added in series with capacitor C1 to damp the potential LC resonance as shown in Figure 17. Boost Output Plug-in Auto Detection Figure 18 provides a solution for auto plug-in detection. External Input Over Voltage Protection Considering the maximum voltage rating at VIN pin, the external OVP circuit as shown in Figure 19 is recommended if input voltage may go higher than 7V. With the enhanced OVP circuit, the design can pass UN38.3. Inductor and Capacitor Selection ACT2801/ACT2801B/ACT2801C supports SMD components. 2.2uH inductor is recommended. Input side, 4.7uF ceramic capacitor in series with 2.7Ω resistor are recommended, on battery side, 22uF ceramic capacitors is recommended while on output side, 2*22uF ceramic capacitors are recommended. Battery Temperature Monitoring ACT2801 continuously monitors the temperature of the battery pack by sensing the resistance of its thermistor, and suspends charging if the temperature of the battery pack exceeds the safety 900 750 600 450 300 150 0 Output current(A) 0 0.2 0.4 0.6 0.8 1.0 1.2 Figure 15. VIOST VS. output current VBAT = 3.7V RIOST=97.6kΩ ) (m cs R ) (m R 25 ) (k RIMC (7) (6) VIN Input VOUT Rcs SW L Output Battery package R: Battery Impedance R BAT Cout RIMC RIMC IBAT Figure 16. Battery impedance compensation setting circuit 3 - BAT BAT 10 ) m ( R ) A ( I ) V ( BAT ) V ( V RIMC(KΩ) 50 100 200 Battery Impedance R(mΩ) Rcs=25mΩ 50 100 200 Rcs=50mΩ 100 200 400 VIN Rcs 50mΩ SW Battery BAT L 2.2uH C1 4.7uF R1 2.7Ω Input Figure 17. Input over voltage surge protection circuit HZ PB Rcs 50mΩ SW Battery BAT L 2.2uH + - D+ D- COUT VOUT 2.2uF USB Shielding Ground PB 2.2uF 715K 200K VBAT 715K Figure 18. Boost output auto detection circuit Figure 19. Input over voltage protection D1 5.6V 10k 10k Si2365EDS VIN Input 3906 Q1 Q2 2.7Ω 4.7uF 4.7k |
|
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |