30 | Keysight | InfiniiVision 4000 X-Series Oscilloscopes - Data Sheet

Waveform measurements and cursors

Single cursor accuracy: ± [DC vertical gain accuracy + DC vertical offset accuracy + 0.21% full

scale]

Cursors

2 pairs of XY cursors

Automatic measurement of positions, ∆X, 1/∆X, ∆Y, and ∆Y/∆X

Automatic measurements

Measurements continuously updated with statistics. Cursors track last selected measurement.

Select up to four measurements from the list below:

Voltage

Peak-to-peak, maximum, minimum, amplitude, top, base, overshoot, pre-shoot, average- N

cycles, average- full screen, DC RMS- N cycles, DC RMS- full screen, AC RMS- N cycles, AC

RMS- full screen (standard deviation), ratio (RMS1/RMS2)

Time

Period, frequency, counter, + width, - width, burst width, duty cycle, bit rate, rise time, fall time,

delay, phase, X at min Y, X at max Y

Count

Positive pulse count, negative pulse count, rising edge count, falling edge count

Mixed

Area- N cycles, area- full screen

Automatic measurement logging

Available via BenchVue

Counter

Built-in frequency counter

Source

Any analog or digital channel

Resolution

5 digits. Up to 8 digits with an external reference 10 MHz input

Max frequency Bandwidth of oscilloscope

Mask limit test option

Standard mask/limit test capability that provides easy, fast pass/fail comparison of a signal

under test to a predefined mask template or auto-mask template. Predefined mask templates or

edits to an auto-mask template can be made via a simple text editor. > 270,000 mask tests per

second (waveform update rate)

Waveform math

Number of math functions

Four (display one at a time)

Arithmetic

Add, subtract, multiply, divide, differentiate, integrate, FFT, Ax + B, squared, square root, absolute, common log,

natural log, exponential, base 10 exponential, LP filter, HP filter, averaged value, smoothing, envelope, magnify,

max hold, min hold, measurement trend, chart logic bus (timing or state)

FFT

Up to 64 kpts resolution. FFT window types: Hanning, flat top, rectangular, Blackman-Harris, Bartlett

1� Denotes warranted specifications, all others are typical. Specifications are valid after a 30-minute warm-up period and ± 10 °C from firmware calibration

temperature.

2. 1 mV/div and 2 mV/div is a magnification of 4 mV/div setting. For vertical accuracy calculations, use full scale of 32 mV for 1 mV/div and 2 mV/div sensitivity

setting�

3� Suspend, resume, reset, bit stuff error, and SE1 error are USB 2.0 low and full speed only.

Trigger type selections

CXPI (Option)

Trigger on the start of frame (SOF), the end of frame (EOF), PTYPE, frame ID, data and info frame ID, data and info

frame ID (long frame), CRC field error, parity error, inter-byte space error, inter-frame space error, framing error,

data length error, sample error, all errors, sleep frame, wakeup pulse

MIL-STD1553 (Option)

Trigger on MIL-STD 1553 signals on data word start/stop, command/status start/stop, RTA, RTA + 11 bits, and

error conditions (parity, sync, Manchester)

SPI (Option)

Trigger on SPI (serial peripheral interface) data pattern during a specific framing period. Supports positive and

negative chip select framing as well as clock Idle framing and user-specified number of bits per frame. Supports

MOSI and MISO data

UART/RS232/422/485 (Option)

Trigger on Rx or Tx start bit, stop bit, data content, or parity error

USB (Option)

speed, and hi-speed (hi-speed is supported on 1 GHz and 1.5 GHz models only)

SENT (Option)

Trigger on SENT bus. start of fast channel message, start of slow channel message, fast channel SC and data,

slow channel message ID, slow channel message ID and data, tolerance violation, fast channel CRC error, slow

channel CRC error, all CRC errors, pulse period error, successive sync pulses error (1/64)

User-definable Manchester/NRZ

(Option)

Trigger on start-of-frame (SOF), bus value, and Manchester errors

USB PD (Option)

Trigger on preamble, EDP, ordered sets, preamble errors, CRC errors, header content (control messages, data

messages, extended messages and value in HEX)

Oscilloscope Experience Redefined:

InfiniiVision 4000 X-Series Performance Characteristics (Continued)