CP20.241-R1, CP20.241-R2, CP20.241-R3,

CP20.242-R2, CP20.242-R2-C1

CP-Series

Jan. 2018 / Rev. 0.2 DS-CP20.241-R2-EN - All parameters are typical values specified at 230Vac, 50Hz input voltage, 24V, 20A output

load, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0

Germany

15/33

P R E L I M I N A R Y

The terminals are IP20 Finger safe constructed and suitable for field- and factory wiring.

CP20.241-R1

Input

Output

DC-OK-Signal

Type

Quick-connect spring-

clamp termination

Quick-connect spring-

clamp termination

Push-in termination

Solid wire

Stranded wire

American Wire Gauge

AWG 20-10

AWG 20-10

AWG 24-16

Max. wire diameter (including ferrules)

2.8mm

2.8mm

1.6mm

Wire stripping length

10mm / 0.4inch

10mm / 0.4inch

7mm / 0.28inch

Screwdriver

3 mm slotted to open

the spring

CP20.241-R2, CP20.242-R2,

CP20.242-R2-C1

Input

Output

DC-OK-Signal

Type

Plug connector with

screw termination

Plug connector with

screw termination

Plug connector with

screw termination

Solid wire

Stranded wire

American Wire Gauge

AWG 20-12

AWG 24-10

AWG 26-14

Max. wire diameter (including ferrules)

2.4mm

3.2mm

1.8mm

Recommended tightening torque

Max. 0.5Nm, 4.5lb-in

Max. 0.6Nm, 5.3lb-in

Max. 0.8Nm, 7lb-in

Wire stripping length

7mm / 0.28inch

12mm / 0.47inch

6mm / 0.24inch

Screwdriver

3.5mm slotted or cross-

head No 2

3.5mm slotted or cross-

head No 2

3.5mm slotted

Do not unplug the

connectors more often

than 20 times in total

Do not unplug the

connectors more often

than 20 times in total

Do not unplug the

connectors more often

than 20 times in total

CP20.241-R3

Input

Output

DC-OK-Signal

Type

Screw termination

Screw termination

Push-in termination

Solid wire

Stranded wire

American Wire Gauge

AWG 20-10

AWG 20-10

AWG 24-16

Max. wire diameter (including ferrules)

2.8mm

2.8mm

1.6mm

Recommended tightening torque

Max. 1Nm, 9lb-in

Max. 1Nm, 9lb-in

-

Wire stripping length

7mm / 0.28inch

7mm / 0.28inch

7mm / 0.28inch

Screwdriver

3.5mm slotted or cross-

head No 2

3.5mm slotted or cross-

head No 2

3mm slotted to open

the spring

Instructions for wiring:

a)

Use appropriate copper cables that are designed for minimum operating temperatures of:

60°C for ambient up to 45°C, 75°C for ambient up to 60°C and 90°C for ambient up to 70°C minimum.

b)

Follow national installation codes and installation regulations!

c)

Ensure that all strands of a stranded wire enter the terminal connection!

d)

Unused terminal compartments should be securely tightened.

e)

Ferrules are allowed and recommended.