LM6584MA datasheet(4/16 Pages) NSC

4 / 16 page

5V AC Electrical Characteristics (Note 13)

Unless otherwise specified, all limits guaranteed for at T

J = 25˚C, VCM =

⁄2V

S and RL =2k

Ω. Boldface limits apply at the tem-

perature extremes.

Symbol

Parameter

Conditions

Min

(Note 6)

Typ

(Note 5)

Max

(Note 6)

Units

Slew Rate (Note 9)

V = +1, VIN = 3.5VPP

V/µs

Unity Gain Bandwidth Product

15.3

MHz

−3dB Frequency

V = +1

MHz

Phase Margin

deg

Settling Time (0.1%)

V = −1, VO = ±1V, RL = 500

Ω

270

Propagation Delay

V = −2, VIN = ±1V, RL = 500

Ω

HD2

nd Harmonic Distortion

IN = 1MHz (Note 10)

OUT =2VPP

−53

dBc

HD3

3rd Harmonic Distortion

IN = 1MHz (Note 10)

OUT =2VPP

−40

dBc

Input-Referred Voltage Noise

f = 10kHz

nV/

Note 1: Note 1: Absolute maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the

device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical

Characteristics.

Note 2: For testing purposes, ESD was applied using human body model, 1.5k

Ω in series with 100pF.

Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the

maximum allowed junction temperature of 150˚C

Note 4: The maximum power dissipation is a function of TJ(MAX), θJA, and TA. The maximum allowable power dissipation at any ambient temperature is

PD =(TJ(MAX) -TA)/ θJA . All numbers apply for packages soldered directly onto a PC board.

Note 5: Typical values represent the most likely parametric norm.

Note 6: All limits are guaranteed by testing or statistical analysis.

Note 7: Large signal voltage gain is the total output swing divided by the input signal required to produce that swing.

Note 8: The open loop output current is guaranteed, by the measurement of the open loop output voltage swing.

Note 9: Slew Rate is the average of the raising and falling slew rates.

Note 10: Harmonics are measured with AV = +2 and RL = 100Ω and VIN =1VPP to give VOUT =2VPP.

Note 11: Continuous operation at these output currents will exceed the power dissipation ability of the device

Note 12: Power dissipation limits may be exceeded if all four amplifiers source or sink 75mA. Voltage across the output transistors and their output currents must

be taken into account to determine the power dissipation of the device

Note 13: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating

of the device such that TJ =TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where TJ > TA.

See applications section for information on temperature de-rating of this device.

Connection Diagram

14-Pin SOIC/TSSOP

20059202

Top View

Ordering Information

Package

Part Number

Package Marking

Transport Media

NSC Drawing

14-Pin SOIC

LM6584MA

95 Units/Rail

M14A

LM6584MAX

2.5k Units Tape and Reel

14-Pin TSSOP

LM6584MT

95 Units/Rail

MTC14

LM6584MTX

2.5k Units Tape and Reel

LM6584MA датащи(PDF) 4 Page - National Semiconductor (TI)

LM6584MA датащи(HTML) 4 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

датащи скачать

ссылки URL