P6002ACMC datasheet(129/212 Pages) TECCOR

129 / 212 page

GR 1089–Core

4 - 5

http://www.teccor.com

SIDACtor® Data Book and Design Guide

+1 972-580-7777

AC Power Fault Test is that the EUT may be damaged, but it may not become a fire,

fragmentation, or electrical safety hazard. Passing criteria for the Current Limiter Test is that

the EUT may be damaged but it may not exceed the acceptable time/current criteria (that is,

cannot cause the wiring simulator as shown in Figure 4.2 to open) nor become a fire,

fragmentation, or electrical safety hazard.

The indicator used in measuring fire, fragmentation, and electrical safety hazards is a

bleached, untreated cotton cheesecloth wrapped around the EUT. Compliance with testing

is determined by the absence of ignition, charring, and the ejection of molten material or

fragments.

First Level Lightning Surge Test

To pass the First Level Lightning Surge Test, the EUT must be undamaged and continue to

operate properly after the stress is applied. This is referred to as passing “operationally.”

Table 4.3 presents the conditions for the First Level inter-building criteria. Applicants have

the option to submit their equipment to meet surges 1, 2, 4, and 5 or surges 3, 4, and 5.

Table 4.4 presents the conditions for the intra-building criteria.

Notes:

1. Primary protectors are removed for all tests.

2. For EUT containing secondary voltage limiting and current limiting protectors, tests are to be performed at the indicated voltage(s)

and repeated at a reduced voltage and current just below the operating threshold of the secondary protectors.

3. Test 1 and 2 can be replaced with Test 3 or vice versa.

4. Alternatively, a surge generator of 1.2x50 µs open-circuit voltage waveform (8x20 µs short-circuit current waveform) per

IEEE C62.41 may be used. The current shall be limited by the inclusion of a series 3

W resistor placed externally to the surge

generator.

5. This test is to be performed on up to 12 Tip and Ring pairs simultaneously.

Notes:

• For EUT containing secondary voltage limiting and current limiting protectors, tests are to be performed at the indicated voltage(s)

and repeated at a reduced voltage and current just below the operating threshold of the secondary protectors.

• Alternatively, a surge generator of 1.2x50 µs open-circuit voltage waveform (8x20 µs short-circuit current waveform) per

IEEE C62.41 may be used. The current shall be limited by the inclusion of a series 6

W resistor for Test 1 and a 12 W resistor for

Test 2, placed externally to the surge generator.

Table 4.3 First Level Lightning Surge Test

Test

(Notes 1 & 2)

Surge Voltage

(VPK)

Waveform

(µs)

Surge Current

per Conductor

(A)

Repetitions

Each Polarity

Test

Connections

(Table 4.1, Figure 4.1)

±600

10x1000

100

2 (Note 3)

±1000

10x360

100

3 (Note 3)

±1000

10x1000

100

4 (Note 4)

±2500

2x10

500

5 (Note 5)

±1000

10x360

Table 4.4 Intra-Building Lightning Surge Test

Test

Surge Voltage

(VPK)

Wave-form

(µs)

Surge Current

per Conductor

(A)

Repetitions Each

Polarity

Test Connections

(Table 4.1, Figure 4.1)

±800

2x10

100

A1, A2

±1500

2x10

100

P6002ACMC датащи(PDF) 129 Page - Teccor Electronics

P6002ACMC датащи(HTML) 129 Page - Teccor Electronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL