64GA106 datasheet(121/330 Pages) MICROCHIP

121 / 330 page

 2010 Microchip Technology Inc.

DS39905E-page 121

PIC24FJ256GA110 FAMILY

8.4.2

OSCILLATOR SWITCHING

SEQUENCE

At a minimum, performing a clock switch requires this

basic sequence:

desired,

read

the

COSCx

bits

(OSCCON<14:12>) to determine the current

oscillator source.

Perform the unlock sequence to allow a write to

the OSCCON register high byte.

Write the appropriate value to the NOSCx bits

(OSCCON<10:8>) for the new oscillator source.

Perform the unlock sequence to allow a write to

the OSCCON register low byte.

Set the OSWEN bit to initiate the oscillator

switch.

Once the basic sequence is completed, the system

clock hardware responds automatically as follows:

The clock switching hardware compares the

COSCx bits with the new value of the NOSCx

bits. If they are the same, then the clock switch

is a redundant operation. In this case, the

OSWEN bit is cleared automatically and the

clock switch is aborted.

If a valid clock switch has been initiated, the

LOCK (OSCCON<5>) and CF (OSCCON<3>)

bits are cleared.

The new oscillator is turned on by the hardware

if it is not currently running. If a crystal oscillator

must be turned on, the hardware will wait until

the OST expires. If the new source is using the

PLL, then the hardware waits until a PLL lock is

detected (LOCK = 1).

The hardware waits for 10 clock cycles from the

new clock source and then performs the clock

switch.

The hardware clears the OSWEN bit to indicate a

successful clock transition. In addition, the

NOSCx bit values are transferred to the COSCx

bits.

The old clock source is turned off at this time,

with the exception of LPRC (if WDT or FSCM is

enabled) or SOSC (if SOSCEN remains set).

A recommended code sequence for a clock switch

includes the following:

Disable interrupts during the OSCCON register

unlock and write sequence.

Execute the unlock sequence for the OSCCON

high byte by writing 78h and 9Ah to

OSCCON<15:8>

two

back-to-back

instructions.

Write new oscillator source to the NOSCx bits in

the instruction immediately following the unlock

sequence.

Execute the unlock sequence for the OSCCON

low

byte

writing

46h

and

57h

OSCCON<7:0> in two back-to-back instructions.

Set the OSWEN bit in the instruction immediately

following the unlock sequence.

Continue to execute code that is not

clock-sensitive (optional).

Invoke an appropriate amount of software delay

(cycle counting) to allow the selected oscillator

and/or PLL to start and stabilize.

Check to see if OSWEN is ‘0’. If it is, the switch

was successful. If OSWEN is still set, then check

the LOCK bit to determine the cause of failure.

The core sequence for unlocking the OSCCON register

and initiating a clock switch is shown in Example 8-1.

EXAMPLE 8-1:

BASIC CODE SEQUENCE

FOR CLOCK SWITCHING

EXAMPLE 8-2:

BASIC CODE SEQUENCE

FOR CLOCK SWITCHING

Note 1:

The processor will continue to execute

code throughout the clock switching

sequence. Timing-sensitive code should

not be executed during this time.

Direct clock switches between any

Primary Oscillator mode with PLL and

FRCPLL mode are not permitted. This

applies to clock switches in either direc-

tion. In these instances, the application

must switch to FRC mode as a transition

clock source between the two PLL

modes.

;Place the new oscillator selection in W0

;OSCCONH (high byte) Unlock Sequence

MOV

#OSCCONH, w1

MOV

#0x78, w2

MOV

#0x9A, w3

MOV.b

w2, [w1]

MOV.b

w3, [w1]

;Set new oscillator selection

MOV.b

WREG, OSCCONH

;OSCCONL (low byte) unlock sequence

MOV

#OSCCONL, w1

MOV

#0x46, w2

MOV

#0x57, w3

MOV.b

w2, [w1]

MOV.b

w3, [w1]

;Start oscillator switch operation

BSET

OSCCON,#0

//Write new "value" to OSCCONH to

set the new oscillator selection

__builtin_write_OSCCONH(value);

//Set the OSWEN bit to start the oscillator

switch operation

__builtin_write_OSCCONL(OSCCON | 0x01);

64GA106 датащи(PDF) 121 Page - Microchip Technology

64GA106 датащи(HTML) 121 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL