ATmega16 datasheet(107/357 Pages) ATMEL

107 / 357 page

107

2466S–AVR–05/09

ATmega16(L)

Figure 48. Phase and Frequency Correct PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV1) is set at the same timer clock cycle as the OCR1x

Registers are updated with the double buffer value (at BOTTOM). When either OCR1A or ICR1

is used for defining the TOP value, the OC1A or ICF1 Flag set when TCNT1 has reached TOP.

The Interrupt Flags can then be used to generate an interrupt each time the counter reaches the

TOP or BOTTOM value.

When changing the TOP value the program must ensure that the new TOP value is higher or

equal to the value of all of the Compare Registers. If the TOP value is lower than any of the

Compare Registers, a compare match will never occur between the TCNT1 and the OCR1x.

As Figure 48 shows the output generated is, in contrast to the phase correct mode, symmetrical

in all periods. Since the OCR1x Registers are updated at BOTTOM, the length of the rising and

the falling slopes will always be equal. This gives symmetrical output pulses and is therefore fre-

quency correct.

Using the ICR1 Register for defining TOP works well when using fixed TOP values. By using

ICR1, the OCR1A Register is free to be used for generating a PWM output on OC1A. However,

if the base PWM frequency is actively changed by changing the TOP value, using the OCR1A as

TOP is clearly a better choice due to its double buffer feature.

In phase and frequency correct PWM mode, the compare units allow generation of PWM wave-

forms on the OC1x pins. Setting the COM1x1:0 bits to 2 will produce a non-inverted PWM and

an inverted PWM output can be generated by setting the COM1x1:0 to 3 (See Table on page

111). The actual OC1x value will only be visible on the port pin if the data direction for the port

pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or clearing) the

OC1x Register at the compare match between OCR1x and TCNT1 when the counter incre-

ments, and clearing (or setting) the OC1x Register at compare match between OCR1x and

TCNT1 when the counter decrements. The PWM frequency for the output when using phase

and frequency correct PWM can be calculated by the following equation:

The N variable represents the prescaler divider (1, 8, 64, 256, or 1024).

The extreme values for the OCR1x Register represents special cases when generating a PWM

waveform output in the phase correct PWM mode. If the OCR1x is set equal to BOTTOM the

OCRnx / TOP Update

and

TOVn Interrupt Flag Set

(Interrupt on Bottom)

OCnA Interrupt Flag Set

or ICFn Interrupt Flag Set

(Interrupt on TOP)

TCNTn

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

fOCnxPFCPWM

clk_I/O

NTOP

⋅⋅

----------------------------

ATmega16 датащи(PDF) 107 Page - ATMEL Corporation

ATmega16 датащи(HTML) 107 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL