ST7263BHX datasheet(124/145 Pages) STMICROELECTRONICS

124 / 145 page

ST7263BDx ST7263BHx ST7263BKx ST7263BE

124/145

Communication interface characteristics (Cont’d)

14.10.2 SCI - serial communication interface

Subject to general operating condition for VDD, fCPU, and TA unless otherwise specified.

Refer to I/O port characteristics for more details on the input/output alternate function characteristics (RDI

and TDO).

14.10.3 I2C - Inter IC control interface

Refer to I/O port characteristics for more details on the input/output alternate function characteristics

(SDAI and SCLI).

The ST7 I2C interface meets the requirements of the Standard I2C communication protocol described in

the following table.

(Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified)

Notes:

1. Data based on standard I2C protocol requirement, not tested in production.

2. The device must internally provide a hold time of at least 300ns for the SDA signal in order to bridge the undefined

region of the falling edge of SCL.

3. The maximum hold time of the START condition has only to be met if the interface does not stretch the low period of

SCL signal.

4. At 4MHz fCPU, max.I2C speed (400kHz) is not achievable. In this case, max. I2C speed will be approximately 260KHz.

Symbol

Parameter

Conditions

Standard

Baud

Rate

Unit

fCPU

Accuracy

vs. standard

Prescaler

fTx

fRx

Communication frequency

8MHz

~0.16%

Conventional mode

TR (or RR)=128, PR=13

TR (or RR)= 32, PR=13

TR (or RR)= 16, PR=13

TR (or RR)= 8, PR=13

TR (or RR)= 4, PR=13

TR (or RR)= 16, PR= 3

TR (or RR)= 2, PR=13

TR (or RR)= 1, PR=13

300

1200

2400

4800

9600

10400

19200

38400

~300.48

~1201.92

~2403.84

~4807.69

~9615.38

~10416.67

~19230.77

~38461.54

Symbol

Parameter

Standard mode I2C

Fast mode I2C 4)

Unit

Min 1)

Max 1)

Min 1)

Max 1)

tw(SCLL)

SCL clock low time

4.7

1.3

µs

tw(SCLH)

SCL clock high time

4.0

0.6

tsu(SDA)

SDA setup time

250

100

th(SDA)

SDA data hold time

0 3)

0 2)

900 3)

tr(SDA)

tr(SCL)

SDA and SCL rise time

1000

20+0.1Cb

300

tf(SDA)

tf(SCL)

SDA and SCL fall time

300

20+0.1Cb

300

th(STA)

START condition hold time

4.0

0.6

µs

tsu(STA)

Repeated START condition setup time

4.7

0.6

tsu(STO)

STOP condition setup time

4.0

0.6

µs

tw(STO:STA) STOP to START condition time (bus free)

4.7

1.3

µs

Capacitive load for each bus line

400

ST7263BHX датащи(PDF) 124 Page - STMicroelectronics

ST7263BHX датащи(HTML) 124 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL