ST72325 datasheet(158/193 Pages) STMICROELECTRONICS

158 / 193 page

ST72325

158/193

12.8 I/O PORT PIN CHARACTERISTICS

12.8.1 General Characteristics

Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.

Figure 79. Unused I/O Pins configured as input

Figure 80. Typical IPU vs. VDD with VIN=VSS

Notes:

1. Data based on characterization results, not tested in production.

2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.

3. When the current limitation is not possible, the VIN maximum must be respected, otherwise refer to IINJ(PIN) specifica-

tion. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS. Refer to section 12.2.2

on page 143 for more details.

4. Configuration not recommended, all unused pins must be kept at a fixed voltage: using the output mode of the I/O for

example and leaving the I/O unconnected on the board or an external pull-up or pull-down resistor (see Figure 79). Data

based on design simulation and/or technology characteristics, not tested in production.

5. The RPU pull-up equivalent resistor is based on a resistive transistor (corresponding IPU current characteristics de-

scribed in Figure 80).

6. To generate an external interrupt, a minimum pulse width has to be applied on an I/O port pin configured as an external

interrupt source.

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

VIL

Input low level voltage 1)

CMOS ports

0.3xVDD

VIH

Input high level voltage 1)

0.7xVDD

Vhys

Schmitt trigger voltage hysteresis 2)

0.7

IINJ(PIN)

Injected Current on PB0 (Flash de-

vices only)

VDD=5V

0+4

Injected Current on an I/O pin

± 4

ΣIINJ(PIN)3)

Total injected current (sum of all I/O

and control pins)

± 25

Input leakage current

VSS≤VIN≤VDD

±1

µA

Static current consumption

Floating input mode4)

400

RPU

Weak pull-up equivalent resistor 5)

VIN=VSS

VDD=5V

120

250

Ω

CIO

I/O pin capacitance

tf(IO)out

Output high to low level fall time 1)

CL=50pF

Between 10% and 90%

tr(IO)out

Output low to high level rise time 1)

tw(IT)in

External interrupt pulse time 6)

1tCPU

10k

Ω

UNUSED I/O PORT

ST7XXX

10k

Ω

UNUSED I/O PORT

ST7XXX

VDD

Note: I/O can be left unconnected if it is configured as output

greater EMC robustness and lower cost.

(0 or 1) by the software. This has the advantage of

22.5

33.5

4.5

55.5

Vdd(V)

Ta=1 40°C

Ta=9 5°C

Ta=2 5°C

Ta=-45 °C

ST72325 датащи(PDF) 158 Page - STMicroelectronics

ST72325 датащи(HTML) 158 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL